Sometimes, the Sharp TV gets stuck on the logo screen while turning it on, which can be frustrating. This issue often arises due to outdated firmware, a faulty main board, or hardware malfunction. If you are experiencing this issue and need to know what happened, we are here to assist. This article offers several troubleshooting methods to fix the Sharp TV stuck on the logo issue.
Causes and Fixes for Sharp TV Stuck on the Logo
| Reasons | Fixes |
|---|---|
| A technical glitch in the software | 1. Power cycle the Sharp TV 2. Restart the Sharp TV |
| Problems with the power socket | 1. Connect the TV cord to a different port |
| Issues with external HDMI connections | 1. Check and replace the HDMI cable 2. Remove connected devices |
| Hardware failure | 1. Repair the defective component 2. Contact Sharp TV customer support |
How to Fix Solve Sharp TV Stuck on the Logo Screen
If your Sharp Roku, Aquos, Android, or Google TV has stuck on the logo screen, follow these troubleshooting methods in the same order to fix it.
Restart Sharp TV
In case of minor glitches or bugs, your Sharp TV will stay on the logo screen for a long time. Restarting is a preliminary solution that can clear out such issues. With the help of a remote control, you can reboot your Sharp TV so it won’t get stuck on the logo screen the next time you turn it on.
1. Press the Power button on the Sharp TV remote to turn the TV off.
3. Wait for a few minutes. Press the Power button on the remote and switch on your Sharp TV.
4. Check if the TV’s interface goes beyond its logo screen. In most cases, it would get solved. But if it doesn’t work, you can power cycle your TV and solve it.
Power Cycle the Sharp TV
If your Sharp TV is not used for a longer duration, it will get stuck when powered up. To fix this, power cycle the Sharp TV to refresh its functions and remove the residual power.
1. Turn off your Sharp TV by removing the TV cord from the electrical socket.
2. To complete the process, hold the Power button on your Sharp TV at the bottom or side of the TV for at least 30 seconds.
3. Release the button and insert the TV’s power cable into the socket.
4. Turn on the Sharp TV and check if it is not stuck on the logo screen. If it doesn’t work, try the next solution.
Reload the Firmware
If the firmware encounters an error during installation, it may cause the Sharp TV to get stuck on the logo screen. You can fix this issue immediately by restarting or power cycling the TV. However, there is a chance the issue will occur next time. To avoid this, you should manually update the Sharp TV firmware by connecting a USB drive that contains the latest software file.
Unplug and Replug the Sharp TV
If the power socket has power supply issues, the TV may get stuck on the logo screen. Connect your Sharp TV to another power socket, check if it turns back normally, and skip the logo screen. If the socket is far away from the TV, use a surge protector to plug the TV in, which will prevent it from unnecessarily turning off due to a loose connection.
Check/Switch Input Source
To view content on your Sharp TV, you need an input source like a cable TV or HDMI. If the input source or the input ports are at fault, you won’t be able to view anything.
1. Check if all the input ports on your Sharp TV are working. For example, if your input source is HDMI, change it to another port and see if the issue is resolved.
2. Change the input source on your Sharp TV. If the current input source is HDMI, switch to a Coaxial network and check if the TV goes beyond its logo screen.
3. Sometimes, problems with streaming devices like Roku, Firestick, etc., can cause this issue. Connect your streaming device to a different TV and check if it works.
Factory Reset Sharp TV
Sharp TV stuck on the logo screen due to minor technical errors or glitches. A factory reset of Sharp TV deletes all the data stored on your device, including any glitches that have been causing the issue.
You can factory reset your TV via the buttons attached to it when you cannot access the TV settings. However, the physical buttons are available for all Sharp TV models.
1. Turn off the Sharp TV and disconnect the power cord.
2. Locate the Channel Down and Input buttons on the back or the sides of your TV.
3. While holding these buttons, connect the TV cord to the power socket and turn it on.
4. If your Sharp TV turns on by itself, it will load the Service menu.
5. In the Service Mode on Sharp TV, locate the Factory Reset option and scroll over it using the Channel Up and Channel Down buttons.
6. Select the Factory Reset option to begin the resetting process. It will then restart and work correctly.
After a reset, if your Sharp TV is stuck on the logo screen, it means that there is a hardware issue.
Contact Sharp TV Customer Support
If none of the above methods work, contact Sharp TV Customer Support through its official website. Explain all your issues to them and get solutions. Check your Sharp TV warranty and see if there is any possibility of replacing the defective component at no cost. If there is no warranty, take your TV to the nearest Sharp TV Service Centre and replace the spare.
Most of the issues point to motherboard replacement. This procedure requires technical expertise, and you should seek a professional TV technician’s assistance to fix the issue.
Additional Tips to Avoid Sharp TV Stuck on Logo Screen
- Always keep your Shap TV updated whenever a new update is released. It will ensure your TV software is optimized and runs at a better speed without lagging or getting stuck.
- Regularly clean the Sharp TV screen to wipe out the dust and debris. Otherwise, it will cause your Sharp TV to get overheated and stuck on a particular screen.
- Don’t place any objects on the TV’s top area, as they can block airflow and stop heat from releasing away.
- Furthermore, you should service your smart TV from authorized centers once a few years. This will help your Sharp TV last for many years and prevent major repairs.
FAQ
If the Sharp TV logo blinks repeatedly while turning it on, it means that there is a problem with the power supply, T-Con board, or TV panel.
It happened due to a mainboard failure on a Sharp TV. Contact the nearest Sharp TV service center and ask them to replace the TV’s main board to rectify this issue.
